青岛理工大学机械与汽车工程学院;
为了研究电火花线切割工艺参数(脉冲宽度、脉冲间隔、峰值电流、极间电压)对TC4钛合金加工的影响规律,本文通过一组四因素四水平正交试验,以切割速度、加工精度作为评价指标,通过极差分析法研究各工艺参数对钛合金加工的影响程度。试验结果表明:脉冲宽度对切割速度的影响是最大的,峰值电流对加工精度的影响是最大的。在脉冲宽度为24μs、脉冲间隔为30μs、峰值电流为4 A、极间电压为8 V的条件下加工沟槽结构,其槽深为250μm,棱宽为100μm,槽宽为250μm。
| 416 | 7 | 13 |
| 下载次数 | 被引频次 | 阅读次数 |
[1]Hui Z,Liu Z,Cao Z,et al. Effect of cryogenic cooling of tool electrode on machining titanium alloy(Ti-6Al-4V)during EDM[J].Materials and Manufacturing Processes,2016,31(4):475-482.
[2]Bai Q Y,Liu H P,Bi S F,et al. Performance and Research Progress of Oxide Ceramic Coatings by Micro-arc Oxidation on Shipbuilding Titanium Alloy[J]. ZhongguoBiaomianGongcheng(China Surface Engineering),2013,26(1):1-5.
[3]Pramanik A, Islam M N, Basak A K, et al. Optimizing dimensional accuracy of titanium alloy features produced by wire electrical discharge machining[J]. Materials and Manufacturing Processes,2019,34(10):1083-1090.
[4]Nirmal K,Jagadesh T. Numerical simulations of friction stir welding of dual phase titanium alloy for aerospace applications[J].Materials Today:Proceedings,2021, 46:4702-4708.
[5]Lv L,Xi J,Wang W,et al. Development Status and Prospect on Application of Titanium Alloy in Ocean Engineering[J].Metallurgical Engineering, 2015, 2(2):89-92.
[6]刘畅，王辰宇，刘贺，等. 3D打印Ti6Al4V钛合金支架的力学性能及生物相容性[J].中国有色金属学报，2018,28(4):758-765.
[7]Klocke,F.,Welling,D.,Dieckmann,J. Comparison of grinding and WEDM concerning fatigue strength and surface integrity ofTi-6Al-4V components[J]. Procedia Engineering, 2011(19):184-189.
[8]Prasad A. V. S. R.,Ramji,K.,Datta,G.L. An experimental study of wire EDM on Ti-6Al-4Valloy[J]. Progress in Materials Science,2014(5):2567-2576.
[9]Alis,A.,Abdullah,B.,Abbas,N.M. Influence of machine feed rate in WEDM of Ti-6Al-4V with constant current(6A)using brasswire[J]. Proc. Eng., 2012(41):1812-1817.
[10]明平美.精密与特种加工技术[M].北京：电子工业出版社，2011.
[11]Pramanik A,Basak A K,Littlefair G,et al. Methods and variables in Electrical discharge machining of titanium alloy-A review[J]. Heliyon,2020,6(12):e05554.
[12]张成军.实验设计与数据处理[M].北京：化学工业出版社，2009.
[13]邓鹏，董长双.钛合金Ti-6Al-4V的电火花线切割参数试验研究[J].机械设计与制造，2017(1):69-71,75.
[14]贾永龙.正交实验分析孔加工中表面粗糙度的影响因素分析[J].南方农机，2020,51(13):192-193,196.
[15]Shajan K., Shunmugam M. S. Characteristics of WEDM machined Ti-6Al-4V surface[J]. J. Mater. Lett., 2004(58):2231-2237.
[16]焦建成，邢济收，杨大勇.电火花加工中最优加工条件的确定[J].北京机械工业学院学报，2004(1):66-70.
基本信息:
DOI：
中图分类号:TG484
引用信息:
[1]李驰,李一楠.电火花线切割加工钛合金表面微槽工艺参数研究[J].机械,2022,49(01):16-22.
基金信息:
山东省自然科学基金（ZR2017MEE012,ZR2018MEE017）